How to Build a Cable Run for Your Dog

I’ve had my share of Shiba escapes over the years, which is why I’ve written posts like Making the Most of Companion Identification Methods and Tagg – The Pet Tracker aka The Shiba Owner’s Peace of Mind. My youngest Shiba, Zuki, is a master escape artist though. I’ve never had to work so hard to keep a Shiba safe at home!

Why I Built a Cable Run, Even Though I Have a Fenced Yard

When we first adopted Zuki, she escaped from the back yard a couple times. (We managed to catch her, but only because she escaped out the back and ended up in a huge flood ditch that she couldn’t get out of own her own.) She was going under the fence, so I had some guys attach chicken wire to the bottom of the fence and trench it into the ground, all the way around the yard – no more holes and no more digging! Everything was fine for a month or two until I came home from work one night and a cute little dog was staring at me from inside my neighbor’s back yard. I walked over to say hello and IT WAS ZUKI!! As soon as I got close to the fence, she leapt over the fence and into my arms. (My dogs live in the house. My daughter was home and had let Zuki outside just a few minutes before I came home and discovered her in the neighbor’s yard.) After that, we only let her out in the yard dragging a 15 foot training lead. We’d stay outside with her and, if she tried to jump over the fence, we’d grab the lead first. That worked great. Until one day when it didn’t. I was outside with all three dogs, Zuki decided to jump the fence, and I didn’t make it in time to stop her. I had to run through the house and out the front to chase after her. By the time I got out there, she was long gone. Luckily, with the help of neighbors, I tracked her down about 20 minutes later. The training lead still served a purpose too… I probably wouldn’t have been able to catch her if she hadn’t still been dragging it.

After that, the rules changed again — Zuki could only be outside if one of us was holding the other end of her lead or it was secured to the house. That limited her outside fun though, and she stopped getting enough exercise. Enter my brilliant father and his excellent solution. For ~$100 we built a 100 foot cable run for her that gives her plenty of running room and keeps her safely inside the fence.

Why not just use a stake tie out? First, I wanted something permanent, that I wouldn’t have to deal with removing every time the lawn guy comes to mow. Second, I wanted her to have a lot of running room, but not be able to reach a fence, so I needed a long thin space, not a circular space. Last, I wanted to minimize the possibility of her wrapping the cable around herself or anything else.

Recently, I was having an email conversation with a reader who has a young Shiba that escapes easily, like Zuki. She felt like restricting her freedom was making her more likely to look for ways to escape. She needed a way to safely give her pup some room to run. I suggested building a cable run like Zuki’s, which is what prompted me to put all the details together in this post.

Parts and Tools Needed

From Lowe’s, Home Depot, or Your Local Hardware Store

galvanized steel cable like this (not sure if this is the exact size that we used, but it’s similar)
several (we used five) of these thingies called chain rope clips
two of these loopy things
two eye bolt screws big enough for the loopy things to fit through
a nifty little swivel pulley

From the Pet Store

Tools Needed
A hammer, screwdriver, ladder, and – if you’re like me and not handy at all – someone handy.

What To Do With All Those Parts

Decide on two places to place the ends of the cable run. I chose to attach one end to my back door frame and the other end to a tree in the center of the yard. Be sure the cable doesn’t run too close to the fence or anything else your dog can jump over. You don’t want them to jump over something while cabled and end up hanging themselves!
Screw the eye bolt screws in at each end, preferably at 90 degree angles to the eventual cable. Make sure you place them high enough that you won’t have to duck under the cable while walking through the yard. Take into account that the cable WILL sag some in the middle.
Put one loopy thing through one eye bolt screw and run your steel cable through it.
Use two of the chain rope clips here – one to secure the cable and loopy thing and a second to neatly hold the end of the cable.
What you’ll have so far should look something like this:
Consider whether you will need to stop your dog from reaching either end of the cable. If so, you’re going to need to place additional chain rope clips on the cable. (I did not need one on the end by the house, but I did place one about 20 feet from the tree at the other end.) Slide any necessary clips on the cable now, along with the pulley. Make sure you slide them on in the right order, so the pulley can run the full length of cable between whatever clips are necessary.
Put the second loopy thing through the second eye bolt screw and thread the cable through it. Use two clips to secure the cable just like you did on the other end. This end is harder, because you have to pull the cable as tight as possible before screwing the clips on. We didn’t use any special tools for this – just our bare hands – and ours only sags a little. If our cable was longer than 100 feet, I think we would have needed a fence puller to get it nice and tight.
If you’re using clips to stop the dog from reaching one or both ends of the cable, tighten them down now. I used one to stop Zuki from wrapping her tie out cable around the tree at the far end.
Clip one end of the tie out cable to the swivel pulley.
Clip the other end of the tie out cable to the martingale collar. Personally, I keep the collar hanging on the inside door knob of my back door. I slip the collar on Zuki before I even open the door. When she comes back in, I close the door (it will close with the cable running under it) before I slip the collar off.

A note about collars: Never use a choke collar to tie out a dog. However, if you do all this work and then use a regular buckle collar, your dog may pull out of the collar and disappear anyway. This is why I use a martingale collar. Martingales should not be left on 24/7 or left on an unattended dog. They are meant to be used while walking. Be sure the martingale is sized properly. It should close tight enough that your dog can’t back out of it, but not so tight as to endanger the dog. Zuki wears a buckle collar 24/7 with her ID tags and Tagg Pet Tracker on it. The martingale only goes on when she is outside, supervised, on her cable run or when we’re going for a walk.

Acclimating Your Dog

Depending on your dog’s temperament, don’t be surprised if their new run freaks them out a little bit at first. Zuki was afraid of the sound the pulley makes as it whizzes along the cable. She would pull, it would whizz, she would sit down and looked freaked out. For the first week or so, we had to go out with her and walk along moving the pulley by hand. If she was out there alone, she’d stay by house and try to not move the pulley. Suddenly, one day, she just got it. Of course, shortly after that, she chased a squirrel and hit the clip near the end REALLY hard. Oops! It didn’t take her long to figure out what her range is though. Now she runs up and down as fast as she wants and – usually – slows down before hitting the end.

~~ UPDATED January 2014 ~~
We’ve found the "weak link" in this system… last weekend, I was watching Zuki in the yard and suddenly realized she was outside the part of the yard that she should be able to reach! Luckily, she’s learned a pretty good recall (when I’m shaking a bag of treats), so I got her back before she realized she was free to jump the fence. Turns out the pulley broke. (I will post a photo shortly.) For now, her tie out cable is simply clipped directly to the steel cable. It’s a little harder for her to pull back and forth, but it works.

To comment on this post, visit How to Build a Cable Run for Your Dog